top of page

MHP Linear Valve Actuator


Enclosure may vary depending on the specifications of the product (water-proof/explosion-proof, Single-Phase/Three-Phase Power).


RPMTECH's MHP Linear Series products are Electro-Hydraulic Actuators built for linear valves (Gate Valves, Globe Valves, etc.). The MHP Linear Series is a compact, all-in-one solution that is capable of advanced control modes and supports various types of installation (separate installation of the MHP Power-pack and the hydraulic cylinder) for maximum versatility. The actuators do not require a gearbox (the cause of many breakages) allowing for direct and efficient delivery of power for reliable use.


  • Compact, All-in-one Electro-Hydraulic Actuator

  • Does not require gearbox: direct power delivery (high efficiency)

  • Modular design (easy maintenance)

  • Equipped with patented manual hand pump

  • Various installation types (able to install actuator and hydraulic cylinder separately for safety and ease of use)

  • Limit settings and parameter settings are easily accessible

  • Self-diagnosis capabilities and password lock for added security

  • Various advanced control modes (refer below to Control Modes)

  • Audible and visible alarm during abnormality

  • Supports various communication platforms (AIO/DIO, Profibus, etc.)

  • Able to equip with Fail-Safe mechanisms (refer below to Fail-Safe Options)


  • Power: Single-Phase AC 110~220V (50/60 Hz) or Three-Phase AC 380~460V (50/60Hz)

  • Enclosure Rating: IP68 Water-proof or Exd II B T4 Explosion-proof

  • Motor Specs: Bidirectional 0.6kW BLDC Motor (DHP Series: 1.2 kW)

  • Thrust Range: 5,000 N ~ 400,000 N (Contact for higher thrust)

Screen Shot 2020-07-23 at 4.21.14 PM.png

Certifications differ by product specifications.



Electro-Hydraulic Valve Actuators

Electro-Hydraulic Actuators are driven by the hydraulic pressure generated from an electric motor, which is then delivered to the hydraulic cylinder to control the valve.

Compact and All-in-One

Advanced Software

Safe and Reliable

RPMTECH actuators are equipped with hydraulic pressure generators, a high tech controller, and a manual hand pump based on patented technology. The compact, all-in-one design and the modular installation capabilities makes the actuators versatile and easy to conduct maintenance.

RPMTECH actuators support a variety of communication platforms to best fit the needs of the end user. The user can access virtually all settings and advanced control modes via the LCD display. The self-diagnosis feature allows for simple maintenance and maximum efficiency.

RPMTECH actuators are engineered (both software and hardware) to maximize the safety of the user and enhance the reliability of the product. The manual hand pump is engineered based on patented technology and adds more reliability especially during a power loss or emergency. Also, Modular Installation allows for the actuator to be installed at a safe and accessible location.

Actuator Configuration Example


Point of Attachment (Valve)

Gate Valve, Globe Valve

Manual Hand Pump

Built on patented technology

Hydraulic Cylinder

Linear Valve Hydraulic Cylinder

Hydraulic Pressure Generator

MHP (Micro Hydraulic Powerpack)

MHP Linear Valve Actuator

Explosion-proof, Single-Phase, Linear Valve Cylinder


Control Modes

Control Modes

Control modes optimized for flow controlwater-hammer absorption, and valve disk protection

Open / Close

Open and Close at constant speed where the speed is configurable.

(applicable to all models)



Maintains valve at a certain position (configurable every 1%).


Speed Control

The Open/Close operation is divided into 3 sections where the speed and stop time in each section is configurable.



Step Control

Actuator operates slowly at a constant interval to overcome the minimum operating speed of the motor. Absorbs water hammering and increases fluid stability.


*Desired Control Mode(s) must be stated in the Request Quote Form below.

Fail-Safe Options

Fail-Safe Options

Opens or Closes the valve during power loss or emergencies

Spring Return Type:


The hydraulic pressure used to operate the valve simultaneously compresses the spring within the cylinder. During a power loss or emergency, the energy compressed in the spring is released and the hydraulic fluid is directed via the solenoid valve to open or close the primary valve.


Self-Weight Type:


During a power loss or emergency, the actuator will direct the hydraulic fluid to the solenoid valve to close the valve with its own weight.


*Desired Fail-Safe Option must be stated in the Request Quote Form below.

Request Quote

Request Quote

Useful details to include: Power (Single-Phase or Three-Phase), Thrust (N), Enclosure Rating (Water-proof or Explosion-proof), etc.

Try Again

Submitted Successfully!



유지 보수 설명서

Maintenance Manual


 사용자 설명서

User Manual

Document Title

Screen Shot 2020-07-16 at 10.10.45
Screen Shot 2020-07-16 at 10.10.45
Screen Shot 2020-07-16 at 10.10.45
Screen Shot 2020-07-16 at 10.10.45
bottom of page